Inflatable boat Navigator AIR 330 Standard

Description

The Navigator Air 330 inflatable bottom boat has long been the flagship of the model range, along with the Air360

The HDND boat Navigator is designed to operate on large rivers and reservoirs

The design of this model :
1. Expressed deadrise similar to the model Air360
2. 48 cm diameter cylinders and 185 cm wide dimensions
The fittings are made in Ukraine.
4. Pvc material: the main suppliers Taiwan, South Korea, Germany
5. Applies the technology of heat welding
6. A confident exit on the glider with one person weighing 90-100kg is possible with motors 6 ~ 8 hp The location of the captain in these models, provided closer to the center.
7. The optimum motor for the model is 9.8 HP -15 HP
8. the weight of the boat pvc in the range 50kg, of which: benches, oars, pump, set weigh 8kg
9. When transporting can easily fit in the trunk or on the rear seats of a car.
10. This model of boat with an inflatable bottom has a certificate of conformity CE.

Advantage of Navigator Air 330ND (1100 pvc) Standart:

1) The use of multi-layer reinforced pvc with a density of 1100 g/m2, TDS brand, Unisol produced in South Korea.

2) The variable diameter of the cylinders gradually tapering towards the bow of the boat provides excellent stability and good seaworthiness

3) The shape of the boat has 4 annular and 2 longitudinal welds, made by heat welding and provides high tightness of the cylinders. Structurally, the welded seam has a strength much higher than glued, which significantly increases the performance of the craft.

4) The increased diameter of the cylinders up to 48 cm is one of the main indicators of the boat’s seaworthiness when operating on large bodies of water.

5) The inflatable (keel) bottom of low pressure (NDND) almost completely dampens the impacts of small waves.

6) When inflating the inflatable bottom to the required pressure (0.25-0.3), the deck acquires rigidity comparable to that of a solder (plywood) floor.

7) The design of the cylinder ends affects the driving dynamics and maneuverability.

8) The installation of redans consists in cutting off the flow of water from the bottom, spreading from the keel to the sides. Longitudinal redans increase the stability of the boat, provide effective access to the glider, which leads to an increase in speed.

9) The transom spoiler allows you to get a strong connection between the transom and the bottom of the boat and allows you to reduce the overall resistance of the water relative to the movement of the vessel.

Air 330ND Standard equipment:

1) Welded design of boat cylinders with three independent pressurized compartments.
2) The inflatable keel has a 6 cm wide wear-resistant protective bar, which greatly reduces the chance of damage to it when driving in shallow water.

3) Wide fender 9 cm wide. additionally protects the boat cylinders and the cockpit from splashes.

4) Handrails are glued along the outer perimeter of the boat for the safety of passengers.

5) Reinforced laminated transom made of waterproof plywood 24 mm thick. glued into the aft part of the cylinders. An overlay made of moisture-resistant plywood is installed on the inside and outside of the transom. A drain valve is installed at the bottom of the transom.

6) Reinforced transom spoiler protects the lower part of the transom from damage in shallow water and forms an optimal angle of attack of the bottom to the water horizon when entering planing.

7) For attaching the anchor cable, an eye ring is provided in the bow of the boat.

8) To carry the boat, there are 2 handles, which are fixed on the inner ends of the cylinders.

9) Two movable seats are easily adjustable along the entire length of the rails.

10) Complete with two aluminum oars 1.8 meters long.

11) Foot boat pump for 6 liters.

12) PVC boat repair kit (PVC material, glue)

13) Operation manual.

14) Small craft certificate.

15) Packing bag for the boat – 1 pc.

16) Base colors: olive, khaki, light gray, dark gray

17) A variant of the combined color of the boat is possible !!!